|
FUEL SYSTEM - HIGH PRESSURE LINE
|
|
|
|
|
|

|
|
|
| High Pressure Line - Pressure Control Valve
|
|
|
Components Description :
- Main function : To control the injection pressure to the engine's requirements
which are calculated according to engine speed and load.
- Engine speed and load are high : The degree of turbulence in combustion
chamber is very great so the highly pressurized fuel has to optimize
combustion.
- Engine speed and load are low : If injection pressure is too high
in low load stage, the nozzle's penetration will be excessive and part
of the fuel will be sprayed directly onto the sides of the cylinder,
causing the formation of smoke and unburned hydrocarbons.
- Pressure control process :
- Measure the current rail pressure by rail pressure sensor
- Signal to EDC(Electronic Diesel Control)
- Calculate the adequate fuel demand by engine speed and load
- Control the "pressure control valve to reach the required value by
PWM(Pulse-width modulation)
|
|
- Types :
- Outlet control : located at the end of accumulator line and control
the output pressure from H/P pump by increasing or decreasing the total
return fuel quantity
- Inlet control : integrated with H/P pump and control the fuel quantity
from feed pump to high pressure pump
*Merit of Inlet control type
- minimize the increasing fuel temperature only supplying optimized
fuel volume
- driving torque is decreased by 3~4kg-m
*Demerit
- difficult to release unneeded rail pressure in sudden deceleration condition
|
|
|
|
- Sorento uses the Inlet control type pressure
control valve.
|

|
|
|
- Pressure control valve non-energized : The fuel pressurized from
feed pump exceeds the spring force so that the control valve remains
open. The small fuel is used for pump lubrication and last of fuel goes
through the pressure control valve and pressurized by high pump.
- Pressure-control valve energized : When the pressure control valve
is energized it remains closed until equilibrium is reached between
the high pressure forces and spring force with energized electromagnet
force The fuel from feed pump side can not go through the pressure
control valve and only return through the return passage inside of the
pump. The electromagnet's forces are proportional to its energizing
current which is varied by pwm(pulse-width modulation) pulsing.
|
|

|
|
-Idle (800rpm):
Close duty
45%
Rail pressure
270bar
|
-Ioaden condition(4500rpm):
Close duty
35%
Rail pressure
1350bar
|
|

|
|
|
|
High Pressure Line - High Pressure Pump
Components Description :
- Main functions :
The high pressure pump is the interface between the low pressure and the
high pressure stages. It is responsible for generating adequate high pressure
under all operating conditions.
|
|
-Type :
- Volumetric blade type driven by timing chain.
- Installed at the same point as a conventional distributor pump.
|
|

|
|
- Main components :
- Drive shaft
- Eccentric cam.
- Pumping element with pump piston
- Inlet valve
- Outlet valve
|
|

|
|
- Operation :
- The feed pump pumps fuel from the tank to the high pressure pump.
- The drive shaft with its eccentric cams moves the three pump plungers
up and down in accordance with the shape
of the cam.
- The inlet valve closes when the pump piston passes through BDC.
- The increasing pressure in the pumping element chamber opens the
outlet valve.
- The compressed fuel enters the high pressure circuit.
|
|
|
|
Items
|
Data
|
Items
|
Data
|
|
Output quantity
|
0.677 /rev
|
Max.rev. Speed
|
4600rpm
|
|
Output pressure
|
1600bar
|
Working pressure
|
1350bar
|
|
Gear ratio
|
0.67
|
Drive torque
|
24~28Nm
|
|
|
|
|
High Pressure Line - Common Rail
Components Description :
|
|
Main functions :
The high pressure accumulator, generally speaking common rail, stores
the fuel at high pressure. Even when large quantities of fuel are extracted,
the common rail maintains its inner pressure practically constant.
|
|
- Components :
- Rail
- Inlet from the high pressure pump
- Rail pressure sensor
- Pressure limiter valve
- Line to the injector
|

|
|
High Pressure Line - Pressure Limiter Valve
|
|
- Main functions :
- the same job as an overpressure valve.
- In case of excessive pressure in common rail, the pressure limiter
valve limits the rail pressure by opening an escape passage.
- Defined opening rail pressure : 1,750 bar
- Components :
- High pressure connection
- Flow passage
- Plunger
- Spring
- Fuel return
- As soon as the maximum system pressure is exceeded, the plunger
is forced up by the rail pressure against the force of the spring. When
the plunger is up, fuel leaves the rail so that the rail pressure drops.
|

|
|
|
|
High Pressure Line - Injector
Components Description :
|
|
- Main function :
The central-vertically located injector injects the correct amount
of fuel into the combustion chamber at the right time.
To do so, it is designed :
- to be fully electronically controlled
- to allow multiple injections with short intervals between each injection
Initial operating currency : 0V/20A
|

|
|
|
|
- Components :
Fuel return
- Electrical connection
- Solenoid valve
- Fuel inlet
- Valve ball
- Bleed orifice
- Feed orifice
- Valve control chamber
- Valve control plunger
- Feed passage
- Nozzle needle
|

|
|
- Operation :
- Injector closed (at-rest status) :
The solenoid valve is not energized and the bleed orifice closed. The
valve spring forces. The valve ball to the bleed orifice seat. The same
pressure is present between in the valve control chamber and in the
nozzle chamber.
- Injector opens(start of injection) :
The solenoid valve is energized with the pick-up current and the applied
force exceeds that of the valve spring which opens the bleed orifice.
When the bleed orifice opens, fuel can flow from the valve control chamber
to the fuel tank via the fuel return. This makes pressure unbalance
between the valve control chamber and the nozzle chamber. The reduced
pressure in the valve control chamber lets the nozzle needle opens as
a result and injection starts.
- Injector closed (end of injection) :
As soon as the solenoid valve is no longer energized, the valve spring
forces the armature downwards and the valve ball closes the bleed orifice.
Closing the bleed orifice leads to pressure buildup in the control chamber.
Consequently this pressure buildup makes pressure balance between in
the valve control chamber and in the nozzle chamber and the nozzle needle
closes.
- Injection time sequence :
|
|
|
A = Control current
B = Stroke in mm
C = High pressure
D = Injection rate
a = Control current for solenoid coil
b = Valve lift stroke
c1 = Pressure in the control chamber
c2 = P. in the needle lift chamber
d = Injection
|

|
|
- Injector control :
- Capacitor disharge
- Injector pull in current
- Capacitor charge
- Injector holding current
- Capacitor charge (PST off)
- Regulated holding current (free-wheeling)
- Regulated holding current (power stage on)
|

|
|
|
|
- Pre-injection :
|
|

|
|
1 = Pre-injection
2 = Main injection
|
1a = Combustion pressure with pre-injection
2a = Combustion pressure without pre-injection
|
|
|
|
- Aim of pre-injection :
Reduction in :
- Combustion noise
- HC Emissions
- Fuel consumption (late injection start)
- Working condition : Idling and operation under partial load
- Principle : In a diesel engine, combustion does not start
immediately after the fuel has been Injected into the cylinder. It makes
severe combustion noise when ignition happens. To reduce combustion
noise and to make idle combustion, it is necessary to reduce the ignition
time by increasing both the vaporisation and the chemical formation.
This increase can be brought about by injecting a small quantity before
the start of the main injection. This is termed pre-injection.
|
|
|
|
Injector installation:
|
|

|
|
|