COMPONENTS

 

MAJOR COMPONENT

  • SRS CM
  • D.A.B. MODULE
  • C.A.B. MODULE
  • P.A.B. MODULE
  • SEAT TRACK SENSOR (Driver & passenger)
  • SEAT BELT PRETENTIONER (Driver & passenger)
  • SRS SRI
  • FRONT IMPACT SENSOR
  • SIDE IMPACT SENSOR
  • BUCKLE SWITCH

 

OPERATING SEQUENCE

  • CRASH
  • CRASH SENSING
  • IGNITION THE INFLATOR
  • PRODUCE GAS TO DEPLOY AIRBAG
  • BAG DEPLOYING
  • FULL DEPOLYMENT OF THE BAG
  • PROTECT THE FRONT OCCUPANTS
  • VENT GAS (BAG DEFLATION)
  • AIR BAG SYSTEM COMPLETED

 

AIRBAG SYSTEM OPERATING SEQUENCE

 

Components , Location

 

DAB


1st squib   












2st squib

 

INFLATOR ASSEMBLY

1. Ignition system
2. Autoignition charge
3. Inflator housing
4. Filter system
5. Initiator
6. Gas generator
7.Connector with integral
    shorting clip

 

AIRBAG MODULE (PAB)

  • Inflator Assembly (Depowered)
  • Mounting plate
  • Module cover (Trim cover)
       "U"-pattern tear seam
  • Bag : not coated -- 140 L
    No-VENT HOLES

 

AIRBAG FIRING SEQUENCE

The firing circuit for the inflator will be activated in the following sequence for deployment (Tf is the instant at which the deployment decision is made)

 

Optimum Firing Time Calculation

  • The airbag must be inflated 80% when the driver reaches 125mm forward displacement
  • The airbag (driver=60 l, passenger=140 l) takes 30ms to reach 80% inflation
  • 125mm forward displacement is reached after 40-80ms depending on the impact velocity
  • The Fire / No Fire decision must be reached by the crash algorithm 10-50ms after impact
  • The optimum firing time is obtained by:
      * Crash film analysis Double integral of acceleration

 

TFire = T125mm Forward Displacement - 30ms Airbag Inflation TimeCONTROL

 

MODULE (ESPS)>T.B.D. angle  Within 30 °from vehicle's centerline : LAW  

Within 45 °from vehicle's centerline : Maker

>Hard object The vehicle crashed a deer with 80 Km/h, but the airbag did not operate.
>T.B.D. velocity9 MPH or below    -----------   Not deploy

 

9 - 12 MPH     ----------------  Deploy or not
12 MPH or above  -----------   Must deploy

 

WIRING HARNESS

All airbag circuits are designated as such and contained in a special overlay harness. Color coding and unique identification in proper locations throughout the overlay harness is recommended. Front end wire routings and connections should be reviewed with particular emphasis on the airbag circuits, maintaining electrical continuity in the event of collision.

 

Curtain Air Bag Module

 

CONTROL MODULE  (SMART)

The primary functions are
-Crash Detection
-Activation of the front airbags, side airbags and belt    pretensioners
-Monitoring of the airbag restrain system
-Indicate system readiness and faults to the driver by means of a fault warning lamp
-Facilitate servicing capability via a serial diagnostic communication interface (Hi_Scan pro)  Main
Functions
-Longitudinal and orthogonal central acceleration sensor
-One firing circuit with Energy Reserve for 1st stage DAB
-Two firing circuit without Energy Reserve for Frontal BPT
-Warning lamp for system fault display
-One Service Communication Interface (K-Line),
-Driver and Passenger BS Monitoring and Status-Recording
 

Optional Functions
-One firing circuit with Energy Reserve for 1st stage PAB
-Two firing circuit with Energy Reserve for 2nd DAB & PAB
-Two firing circuit with Energy Reserve for for Curtain  Airbags
-Two Early Crash Sensor Interfaces
-Seat tract sensor Monitoring and Status-Recording

 

Cyclic Measurement

After the start up phase the microcontroller is executing cyclic test on following modules / parts:

  • A/D Converter  (Accelerometer, ±50g)
  • Battery Voltage
  • Firing Loops
  • Warning Lamps
  • Firing Voltage Internal
  • Safing Sensor (Trigger Switch)
  • Seat Track Sensor
  • Early Crash Sensor
  • Buckle Switches

 

Measurements in the start up phase
- Watchdog - EEPROM, ROM, RAM
- Warning Lamps  
- Autonomous Operating Time
- High Side Switch and Low Side Switch Test Acceleration Sensor

 

SAFING SENSOR

The safing sensor is dual contact electromechanical switch, which closes if it experiences a deceleration exceeding a specified threshold.
The operation of the sensor is completely independent of all electronic components in the SRSCM and firing current must flow across the safing sensor contact to activate the squibs.
This provides additional protection against an unwanted deployment for the airbag firing circuits.

 

ACCELEROMETER

The integrated electronic accelerometer provides
an electrical representation of the acceleration
experienced by the vehicle in the longitudinal axis.
This electrical signal is linearly proportional to the
acceleration in G.
The accelerometer is included low   pass filter.
(reduce unwanted noise)

 

SRSCM Connector

2.2   Connector Pinning    (Subject to be changed later) and Coding

25

24

23

22

21

20

19

18

17

16

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

 

50

49

48

47

46

45

44

43

42

41

40

39

38

37

36

35

34

33

32

31

30

29

28

27

26

 

 

 

 

 

 

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

75

74

73

72

71

70

69

68

67

66

65

64

63

62

61

60

59

58

57

56

55

54

53

52

51

•

•

•

•

•

•

•

•

 

 

 

 

•

•

•

•

 

 

 

•

 

•

 

 

 

         Shorting bar trap(SBT)                                                                          NC    Electrical not connected

 

Pin #

Name

Description

1

 Not used

 

2~25

STB

Shorting Bar

26

VBatt

Battery Supply (VBatt)

27

WL

Warning Lamp

29

DAB 1Lo

Front Driver A/Bag Inflator,1 Low

30

DAB 1Hi

Front Driver A/Bag  Inflator, 1High

31

PAB 1Hi

Front A/Bag Passenger Inflator,1 High

32

PAB 1Lo

Front A/Bag Passenger Inflator ,1 Low

33

DBPT Lo

Driver Belt Pretensioner, Low

34

DBPT Hi

Driver Belt Pretensioner, High

35

PBPT Hi

Belt Pretensioner, High (Passenger)

36

PBPT Lo

Belt Pretensioner, Low (Passenger)

37

DCAB Lo

Driver Curtain Airbag, Low

38

DCAB Hi

Driver Curtain Airbag, High

39

PCAB Hi

Passenger Curtain Airbag, High

40

PCAB Lo

Passenger Curtain Airbag, Low

41

DAB 2Lo

Front Driver A/Bag Inflator,2 Low

42

DAB 2Hi

Front Driver A/Bag  Inflator,2 High

43

PAB 2Hi

Front A/Bag Passenger Inflator, 2High

44

PAB 2Lo

Front A/Bag Passenger Inflator, 2Low

45~53

Not used

 

54

K-Line

 

55~57

Not used

 

 

 

 

58

ACOut

Advanced Crash Output

59

Not used

 

60

DSTS

Driver Seat Track Sensor

61

DBSW

Driver Buckle Switch

62

PBSW

Passenger Buckle Switch

63

PSTS

Passenger Seat Track Sensor

64~67

Not used

 

68

PSIS Lo

Passenger Side Impact Sensor Low

69

PSIS Hi

Passenger Side Impact Sensor High

70

DSIS Hi

Driver Side Impact Sensor High

71

DSIS Lo

Driver Side Impact Sensor Low

72

PFIS Lo

Passenger Front Impact Sensor Low

73

PFIS Hi

Passenger Front Impact Sensor High

74

DFIS Hi

Driver Front Impact Sensor High

75

DFIS Lo

Driver Front Impact Sensor Low

 

ECU Location

 

FRONT IMPACT SENSOR

-Faster ACU G Sensor
-Support ACU G Sensor
 

 

Sensor Issues
Acceleration Range +/- 250 g
Shock Resistance up to 1500 g
Mounting Issues Influencing the Signals

  • The impact side and the severity can be derived from the separate sensor signals.
  • Performance of Pole-Tests is dependence on vehicle structure

 

FRONT IMPACT SENSOR

 

 

SIDE  IMPACT SENSOR


Side Sensor Issues
Acceleration Range +/- 250 g
Shock Resistance up to 1500 g
Mounting Issues Influencing the Signals

 

SEAT TRACK SENSOR

 

Service Reminder Indicator (S.R.I.)

Status DisplayAs soon as operating voltage is applied to the CM activates the SRI for a bulb check.  The lamp shall blink  6 times for 6 seconds at 1HZ during the initialization phase and be turned off afterwards.During the initialization phase, the CM will not be ready to detect a crash and deployment will be inhibited until the signals in the CM circuitry stabilize.

  • Loss of ignition voltage supply to the CM: lamp turned on continuously.
  • Loss of internal operating voltage: lamp turned on continuously.
  • Loss of CM operation: lamp flashed at approx. 1Hz by watchdog circuitry.
  • Continuous Reset caused by Watchdog Trigger failure: SRI blinks
  • CM not connected: lamp turned on through shorting bar in wiring harness connector.

 

SERVICE REMINDER INDICATOR

 

Operating situation

Operating method

R
U
N
N
I
N
G

Return to normal from
temporary fault

Faults frequency 5
Active fault

S
T
A
R
T
I
N
G

Normal

Faults frequency 5

Faults frequency 6
Active fault

 

Fault qualification (External fault)

 

SEAT BELT PRETENSIONER

Passive seat belt System
Main construction

  • Gas generator
  • Cylinder & Piston
  • Winding wire
  • Tension reducer
  • Rack & Pinion gear
  • Force limiter
  • ELR mechanism

ELR: Emergency Locking Retractor

 

Function

When a vehicle has crashed with a certain degree of frontal impact, the gas generator is made to ignite by the electrical firing signal from SRSCM.
Gas from the gas generator causes movement of the piston in the manifold
case (cylinder), which operates a rack gear.
Finally the webbing is retracted by the rotation of the spool.
Therefore the seat belt pretensioner helps to reduce the severity of injury tot he front occupant by retracting the seat belt webbing to prevent the occupant from moving forward and hitting the steering wheel or instrument panel when the vehicle is crashed.

 

Characteristics of Pretensioner

- Effective force transmission through use of rack & pinion gear type pretensioner.
- Stable load and free stroke by torsion bar type force limiter.
- Pretensioner with long travel retraction.
     - Mechanical and Electrical types are available.
     
* Caution
  A pretensioner functions one time only.  Be sure to replace the
pretensioner seat belt as new one after activation of it.

 

Force Limiter

Thr force limiter is designed to relieve the
impact force to an occup ant's chest of the
seat belt webbing when the occupant is restrained by the seat belt during a crash.
If the crash force reaches a certain value,
the torsion bar in the pretensioned seat
belt is deformed and this causes the webbing
to be extracted from the seat belt thus
relieving impact force.

 

SEAT BELT PRETENSIONER OPERATION

 

Seat Belt Pretensioner Activation

Under a must-deploy condition, the SRE-SMART will supply firing current to the activators when the microprocessor determines that a deployment is required and activates the firing circuits.  A safing sensor is not implemented.
Each time the seat belt pretensioners are activated an internal counter is incremented.  If this counter reaches the value of 6, the warning lamp is set, and a fault message (SRSCM) internal fault, replace SRSCM is written into the non-volatile memory.  Hereby the SRSCM unit can be reused 5 times after a seat belt pretensioner activation.  After 6 times activation, the Control Module should be replaced as new one.

 

Seat belt pretensioner firing circuit

As an option two additional firing circuit for seat belt pretensioners may be provided.
Each firing circuit can be activated independently.The firing circuits are configured so that there is no low-impedance connection from the squibs to either ground or a positive potential inside the SRE-SMART in the quiescent state.

 

Seat belt pretensioner firing sequence

Systems with optional seat belt pretensioner circuits will normally activate the seat belt pretensioners first and, if the crash is of sufficient strength, deploy the airbags.
The driver's and passenger's pretensioners are activated at the same time.
The firing sequence and ON time for the firing circuits is controlled by the SRE-SMART , and ON time is normally 4ms.

 

Seat belt pretensioner firing current

The optional seat belt pretensioner circuits are supplied with battery voltage.  In case of an activation, an appropriate current flows through the activators via the firing transistors.
This current depends on the actual battery supply voltage and on the resistance of the external firing loops.  In all case, the maximum current is limited to approximately 2 - 3 A by SRE-SMART.

 

Service procedure - Installation

The pyrotechnical triggering ignition system is integrated into the retractor and forms one single component and the pretensioner is operated by an electrical signal.
Care should be taken when handling the pretensioner seat belt.
Before installation, disconnect the battery (-) terminal, with the ignition key on off position.
When installing and removing the pretensioner, do not tap or bang it.- The pretensioner
seat belt must be correctly mounted according to the specified location and direction.

  • Only connect the battery after installation of the pretensioner seat belt has been correctly completed.

 

Service procedure – Removal

It is absolutely necessary to remove the pretensioner seat belt in the sequence described before page.

  • Make sure that ignition is on off position.
  • Disconnect the battery (-) terminal and, make sure it does not come into  contact with the body.
  • Wait for about I minute.
  • Pull off the plug from the appropriate connector at the gas generator.
  • Loosen the belt and remove the belt from the vehicle body.